 |
Legend 37’ Express |
  |
| Dimensions |
Specifications |
| Length (LOA) |
37’ (11.28 meters) |
| Beam |
12’ (3.66 meters) |
| Draft |
28” (0.7 meters) |
| Dead rise (Transom) |
23.5 degrees |
| Displacement, approx. |
12,500 lbs. (dry) (5,669 kilograms) |
| Fuel Capacity |
500 gal. Standard (1,893 liters) |
| Water Capacity |
50 gal. (189 liters) |
| Engine choices (2X) |
MAN D0836LE (450HP) |
| |
YANMAR 6LY2ASTP (440 HP) |
| |
CATAPILLER C-7 (461 HP) |
| |
CATAPILLER C-9 (550 HP) |
| |
CUMMIMS QSC 8.3 (600 HP) |
|
Standard equipment |
Hull
| Oven cured pre-preg epoxy resin |
| Kevlar/E-glass hybrid multi-directional (0/90/+45/-45) stitched fabric reinforcement |
| S-glass multi-directional (0/90/+45/-45) stitched fabric reinforcement |
| Bottom, sides, and transom, cored with high temperature Corecell P 600 |
| Molded carbon fiber stringers with intergraded fuel and water tanks |
| All materials are hand laid, vacuum bagged and post cured (175deg.) in a single step to create a monolithic structure |
| Molded recessed zinc pocket with flow thru cover, flush with transom |
| Molded recessed trim tabs |
| Molded pressurized self cleaning sea chest |
| Propeller tunnels (40% diameter of propeller with 10% tip clearance) |
| Discharge water (bilge, drains, and a/c discharge) exits via scupper boxes, no other hull penetrations exists |
| Stainless steel rub rail on a seamless sheer ( mold seam is 4 inches inboard on the deck) |
| Clear-coat polyurethane finish throughout bilge and engine room areas over Kevlar and carbon fiber fabrics |
| Hull sides Awlgrip polyurethane finish (owners choice of color) |
| Custom boot striping |
| Bottom paint, 2 coats anti-fouling |
| Molded recessed log for flush mounting transducers |
|
Deck
| Oven cured pre-preg epoxy resin |
| S-glass |
| multi-directional stitched fabric reinforcement |
| Carbon fiber woven multi-directional reinforcement |
| Cored with high temperature Corecell P 600 |
| Cored with anti-compressive close cell foam at all mounting points (cleats, rod holders, tower legs) |
| All materials are hand laid, vacuum bagged and post cured (175deg.) in a single step to create a monolithic structure |
| Anchor locker with flush mounted hinges |
| Awlgrip polyurethane finish (owners choice of color) |
| Bow chocks (2) 6 inch CNC machined from anodized billet aluminum, |
| Bow cleats (2) 10 inch CNC machined from anodized billet aluminum, |
| Spring cleats (2) 10 inch CNC machined from anodized billet aluminum |
|
Helm deck
| Seating for 9 adults (2 helm seats ) |
| L – Shaped seating with storage underneath |
| Bench seat with over 7 feet of storage underneath ( port side) |
| Large helm console capable of holding 4 large monitors with view through cover |
| Palm beach style helm pod with single leaver controls made of CNC machined anodized billet aluminum |
| Compass with light, flush mounted |
| Engine instrumentation |
| Emergency engine shut downs |
| Custom switch panel |
| Companion-way door |
| Drink box on helm console |
| Engine access hatch with stainless steel gas shocks |
| Custom cushions with closed cell foam on all seating (can be used for flotation) |
| Courtesy lighting |
| Fire and bilge water level alarms, audible with warning lights |
| Custom helm wheel made of CNC machined anodized billet aluminum |
|
Cockpit
| Port and starboard gaff / rod lockers |
| Shore power connections, port and starboard sides |
| Rod holders (Rupp) x4 |
| Large tackle center (owners choice of draw configuration) |
| Bait freezer (port side) |
| Bait prep sink |
| Rigging station |
| Saltwater wash down |
| Fresh water wash down |
| Large removable insulated fish box with macerator pump-out system |
| Insulated drink box in step |
| 60 gal. live bait well with observation window and halogen light (water proof) |
| Self bailing cockpit with deck drain covers custom made of CNC machined anodized billet aluminum |
| Backing plate for fighting chair |
| Transom door with custom latch custom made of CNC machined anodized billet aluminum |
| Courtesy lighting under gunwells, 12 volt halogen |
| Stern cleats 10 inch, custom made of CNC machined anodized billet aluminum |
| Transom haws pipes custom made of CNC machined anodized billet aluminum |
| Tuna tubes, 2 either side of bait well, 12 & 120 volt |
| Non-skid surface |
|
MECHANICAL
| Acoustic and thermal insulation |
| Bilge pumps, automatic/ manual (3) Rule 2000 with ultimate switches, and indicator lights |
| Double constant toque 316, stainless steel clamps on engine exhaust hoses |
| Double 316 stainless steel hose clamps on all hose fittings where possible |
| Emergency bilge suction valve on one main engine (crash pump) |
| Engine room blowers, reversible Delta T, 12 volt |
| Engine room demister, Delta T |
| Bait well pumps, 12 volt and 110 volt |
| Automatic fire suppression, halon |
| Fresh water cooling on main engines |
| Fuel filters/water separators, Racor |
| Fire retardant fuel lines |
| Engine hour meters (2) |
| Bilge alarm for high water (3) |
| Integrated tanks, fuel, water, and black water |
| Hot water heater, stainless steel, 6 gallon, 110 volts |
| Hydraulic steering |
| Propellers, custom high performance nibral |
| Rub rail, stainless steel |
| Rudders, high performance CNC machined stainless steel, using Tides dripless bearings and carbon fiber upper supports |
| Sea chest with heavy-duty stainless steel seacocks; self-cleaning and pressurized, 6 psi at 35 knots |
| Aqua-met 22 stainless steel shafts, 2 inch, fitted with composite shaft tubes |
| Struts, high performance, recessed and faired flush with bottom of hull. |
| Tides Drip-less shaft seals |
| Oil change system, main engines, generator, and transmission |
| Trim tabs, hydraulic and recessed |
| Pressurized fresh water system 12 volt |
| Pocketed recessed transom Zinc |
| Electronic trolling valves |
| Overboard drain manifold discharging via aft scuppers |
| Custom stainless exhaust risers |
| Engine alarm system |
| Bonding system with transom zinc plate |
| Holding tank, 12 gallon, integrated with monitor, macerator, and dockside discharge |
| Integrated oil holding tank |
| Von Widman under water exhaust system |
|
ELECTRICAL
| 5 KW freshwater cooled diesel generator with remote start, instrumention, safety shutdown, and waterlift muffler |
| Custom AC/DC electric distribution panel |
| Voltmeter and ammeters |
| Reverse polarity indicator |
| Battery parallel switch 3-way |
| Battery condition indicators (3) |
| Vapor proof battery switches (3) |
| Batteries drycell heavy-duty marine (5) |
| Bonded electrical system |
| Circuit protection throughout |
| Engine room lights 12 volts |
| Cabin lights, 12 volt halogen |
| Receptacles 110 volts duplex, ground fault protected |
| Tinted copper wire throughout |
| Battery on/off switch |
| Tank gauges, fuel, potable water, and black water |
| 50' shore cord (1), 30 amp shore power |
| Battery charger, 70 amp automatic with thermal cut out |
| Battery on/off switches, vapor-proof |
| Horn supplied, uninstalled for tower installation |
| Navigation lights, uninstalled for tower installation |
| Airpax 2 wire system |
|
CABIN
| Custom designer interior décor, owners choice of veneers, custom trim, superbly jointed and finished |
| AC duplex outlet/GFI protected |
| Access hatch to bilge |
| Air conditioning/heat including; 10,000 BTU capacity |
| Diagonal double bed portside with 5" mattress, coverlets |
| Hanging locker, cedar lined, starboard side |
| Lighting - recessed halogen (6) |
| Port side rod storage for up to 8 rods with #50 wide reels |
| Positive latches used on all cabinet doors and drawers |
| Selection of fine quality fabrics and coverings throughout |
| Stereo AM/FM CD/DVD |
| Portside lounge converts to upper and lower sleeping berths |
| Overhead cabinets |
| Hanging lockers, cedar lined |
| Vinyl headliner with recessed 12-volt lighting |
| Outlet, 110 volts duplex |
| Storage compartments and large drawers below bed |
| Flat screen TV |
| Upholstered dressing seat |
| Hanging locker, cedar lined |
| Halogen reading lights at head of berth |
|
GALLEY
| AC duplex outlet, GFI protection |
| Ceramic cook-top, one burner, recessed with Corian cover |
| Corian counter top with custom Corian sea rails |
| Positive latches used on cabinet doors and drawers |
| Side by side refrigerator/freezer |
| Counter top lighting - recessed halogen (3) |
| Microwave/convection oven |
| Storage cabinet and drawers, oak sides and cedar bottoms |
| Sink, deep with dual faucet lever |
|
HEAD
| AC duplex outlet/GFI protected |
| Corian counter top, custom |
| Custom vanity |
| Head, Vacuflush electric, with holding tank and pump out system |
| Framed mirror |
| Positive latches used on cabinet doors and drawers |
| Separate stall shower with automatic shower sump pump |
| Toiletry storage cabinet |
| Recessed halogen lighting, DC |
| Sink with dual faucet level |
|
|
|
